No sketch is not running on my D1 Mini Pro. Even not the "Blink"-Sketch.

[Mathias2803]

I was able to flash several "D1 Mini V3" with different Sketches and I never had a problem. But due to the external antenna I decided to get a "D1 Mini Pro".

I am able to flash the sketch on the board without error messages, but then nothing is happening.

I even tried the "Blink" example code, but even with this program I had no success.
When I push the reset button with the connected serial output I get following message:

 ets Jan  8 2013,rst cause:2, boot mode:(3,6)

load 0x4010f000, len 3584, room 16 
tail 0
chksum 0x55
csum 0x55
csum err
ets_main.c 

Here you can see my Arduino IDE settings:

Can anybody help me what I am doing wrong?

Thanks a lot and kind regards Mathias

---

[d-a-v]

Try a full flash erase ("Erase flash" entry).
Also check with esptool.py that your flash is 16MBytes.

[Mathias2803]

Hello, thanks for your feedback.

The esptool.py gives out following information, so the flash size seems to be 16MB:

I also made a a full flash erase as you can see in my settings now:

But after the restart still the same error message and even the example skretch "Blink" is not running:

What else can I do to get it running?

Thanks a lot, kind regards Mathias

[Jason2866]

Try a slower upload speed. I have several devices not working with 921600.
You can try with 115200

[Mathias2803]

I have changed the upload speed to 115200 but still the same error message at the end.

[Jason2866]

There is a high chance that the board is just defect.

[d-a-v]

Another test would be to try another flash mode by selecting the "esp8266 generic board".
D1 is by default DIO, you could try DOUT.

[devyte]

Try also:

• without FS (the ingo above shows 14MB FS)
• selecting 4MB flash size (your flash chip may be fake despite being detected as 16MB)

[Tech-TX]

I'd bet money on the Flash mode David mentioned above. 👍 I wasn't aware that it defaulted to DIO; I thought most of them were DOUT. Since there are probably more cheap clone D1 Mini Pro boards than official Lolin boards, maybe I should do a PR to switch that to DOUT. The error message is a checksum error, which can happen if the chip is in a mode that it can't support at 40MHz. I have a clone D1 Mini Pro V1.x and a couple of real Lolin D1 Mini Pro V2.x boards that work with the current defaults, but that's no guarantee that a clone with cheap Flash from Wo Fat Electronics will work.

[Jason2866]

It seems new crappy boards are out there arendst/Tasmota#11615
Changing flash chip didn´t help.

[d-a-v]

@Mathias2803
Can you provide a photo of your flash chip?
Can you use esptool.py to identify it ?

@Jason2866
I can't seem to understand whether the issue you mention came to a conclusion ?
It seems it's not the flash chip since it has been replaced.
What version of the core is used in these tries ?

@Tech-TX
The DIO configuration for d1 mini was made by @wemos
If a change has to be made, what about

• adding the flash mode menu for wemos boards (with DIO by default)
• adding a new board labeled "wemos d1 mini clone" "wemos d1 mini pro clone" with DOUT

[Jason2866]

@d-a-v i dont think it is the flash chip. Imho the board design is crappy at all.
Core is 2.7.4.x (we added some backports)
I have a batch of (clone) NodeMCU which never did run stable. Only after replacing the ESP8266 chip the worked as expected (with 160Mhz too). The have no ESP-12F module soldered. Builded with ESP8266 and extra Flash chip like the module here and the one in Tasmota discussions

[Mathias2803]

Thanks for all your support. I will try all later. But here is the photo from my board as good as I can do it.

[Mathias2803]

This is the chip I have ordered:
https://a.aliexpress.com/_msEoiOT

[Tech-TX]

Hi, @d-a-v ! I'm willing to do anything that you gentlemen think will help, David. I'll let you folks set the direction. As I'd mentioned above, Wemos doesn't make the D1 Mini Pro any longer, and the authentic Lolin D1 Mini Pro are rare since they cost 2x what a clone board does. Simpler than adding another board type is allowing the Flash mode to be selectable for the D1 Mini Pro with the initial default set to DOUT. That will raise the fewest issues with "my board doesn't work..." I have a couple of boards marked WEM*S (cheap clones), so the name on the board could easily be misleading to newbies.

I'd thought that the default Flash mode was changed to DOUT as it works with nearly all Flash brands, fewer questions & issues. The only weird part I've heard of (haven't seen myself) was Macronix MX25L3205D which only works in DIO mode, not DOUT. That Flash was on a clone D1 Mini that one person was having issues with. The Winbond parts I have work in all 4 modes; I bought 50 of their 4MB parts in case I needed to swap out cheap Flash. ;-)

I was wrong earlier, the Lolin D1 Mini Pro boards I have are v2.0.0, not v3.x.

@Mathias2803 Those photos look like a really cheap clone. I hadn't seen anyone use an unbranded ceramic antenna yet; all of the boards I'd seen use the Rainsun antenna. That likely means the rest of the parts on the board are also floor sweepings. The Flash chip has marking of a Micron 16MB Flash although the chip looks shiny, and the real Micron chips I've seen are a matte finish. That's the hallmark of a rebranded IC, so no telling what the Flash truly is. You can read out the Flash ID with this:
esptool.py -p COMx flash_id (Windoze, where COMx is whatever COM port your board ends up at)

The LDO voltage regulator has the marking used by a Torex XC6102, a 300mA 3.3V regulator (a little underpowered for ESP8266) but again, there's no honor among thieves so it may be a cheap Chinese clone part that only runs 150mA. If the LDO is underrated, there's a quick low-power test you can run that will boot with a 150mA regulator:

#include <user_interface.h>

#define _R (uint32 *)PERIPHS_RTC_BASEADDR
#define valRTC 0xFE000000  // normal value during CONT (modem turned on)

RF_PRE_INIT() {
  *(_R + 4) = 0;  // value of RTC_COUNTER for wakeup from light/deep-sleep (sleep the modem)
  system_phy_set_powerup_option(2);  // stop the RFCAL at boot
  wifi_set_opmode_current(NULL_MODE);  // set Wi-Fi to unconfigured, don't save to flash
  wifi_fpm_set_sleep_type(MODEM_SLEEP_T);  // set the sleep type to Forced Modem Sleep
}

void preinit() {
  *(_R + 4) = 0;  // sleep the modem again after another initialize attempt before preinit()
  wifi_fpm_open();  // enable Forced Modem Sleep
  wifi_fpm_do_sleep(0xFFFFFFF);  // enter Modem Sleep mode
  // won't go into Forced Modem Sleep until it sees the delay() in setup()
}

void setup() {
  *(_R + 4) = valRTC;  // Force Modem Sleep engaged, set the modem back to 'normal' briefly
  delay(1);  // and sleep the modem at 18mA nominal substrate current
  Serial.begin(74880);  // bootloader baud rate so you can also see the boot message
  pinMode(LED_BUILTIN, OUTPUT);
}

void loop() {
  Serial.println("I'm alive!");
  digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));
  delay(500);
}

You can either monitor the serial port at 74880 baud or watch the blinky LED to see that it booted correctly. If that runs, then I'd immediately file a complaint with the seller you bought from as there's no way the board will work with WiFi on.