touch.ino

#include <unity.h>
#include "soc/soc_caps.h"

#if SOC_TOUCH_SENSOR_NUM > 0

#include "driver/touch_pad.h"

#if CONFIG_IDF_TARGET_ESP32

#define TEST_TOUCH_CHANNEL   (9)
static touch_pad_t touch_list[TEST_TOUCH_CHANNEL] = {
    TOUCH_PAD_NUM0,
    //TOUCH_PAD_NUM1 is GPIO0, for download.
    TOUCH_PAD_NUM2,
    TOUCH_PAD_NUM3,
    TOUCH_PAD_NUM4,
    TOUCH_PAD_NUM5,
    TOUCH_PAD_NUM6,
    TOUCH_PAD_NUM7,
    TOUCH_PAD_NUM8,
    TOUCH_PAD_NUM9
};

uint8_t TOUCH_GPIOS[] = {4,2,15,13,12,14,27,33,32};

#define NO_TOUCH_GPIO 25

#define RELEASED_VALUE        80 //80+ read value to pass test
#define PRESSED_VALUE         20 //20- read value to pass test
#define INTERRUPT_THRESHOLD   40

#else //ESP32S2 and ESP32S3

#define TEST_TOUCH_CHANNEL   (12) //14
static touch_pad_t touch_list[TEST_TOUCH_CHANNEL] = {
    TOUCH_PAD_NUM1,
    TOUCH_PAD_NUM2,
    TOUCH_PAD_NUM3,
    TOUCH_PAD_NUM4,
    TOUCH_PAD_NUM5,
    TOUCH_PAD_NUM6,
    TOUCH_PAD_NUM7,
    TOUCH_PAD_NUM8,
    TOUCH_PAD_NUM9,
    TOUCH_PAD_NUM10,
    TOUCH_PAD_NUM11,
    TOUCH_PAD_NUM12
    //TOUCH_PAD_NUM13, //Wrong reading
    //TOUCH_PAD_NUM14
};

uint8_t TOUCH_GPIOS[] = {1,2,3,4,5,6,7,8,9,10,11,12/*,13,14*/};

#define NO_TOUCH_GPIO 17

#if CONFIG_IDF_TARGET_ESP32S2
  #define RELEASED_VALUE        10000 //10000- read value to pass test
  #define PRESSED_VALUE         42000 //40000+ read value to pass test
  #define INTERRUPT_THRESHOLD   30000
#elif CONFIG_IDF_TARGET_ESP32S3
  #define RELEASED_VALUE        25000 //25000- read value to pass test
  #define PRESSED_VALUE         90000 //90000+ read value to pass test
  #define INTERRUPT_THRESHOLD   80000
#else
  #error Test not currently supported on this chip. Please adjust and try again!
#endif

#endif

bool touch1detected = false;
bool touch2detected = false;

void gotTouch1() {
  touch1detected = true;
}

void gotTouch2() {
  touch2detected = true;
}

/*
 * Change the slope to get larger value from touch sensor.
 */
static void test_press_fake(touch_pad_t pad_num) {
  touch_pad_set_cnt_mode(pad_num, TOUCH_PAD_SLOPE_1, TOUCH_PAD_TIE_OPT_DEFAULT);
}

/*
 * Change the slope to get smaller value from touch sensor.
 */
static void test_release_fake(touch_pad_t pad_num) {
  touch_pad_set_cnt_mode(pad_num, TOUCH_PAD_SLOPE_7, TOUCH_PAD_TIE_OPT_DEFAULT);
}


/* These functions are intended to be called before and after each test. */
void setUp(void) {
  
}

void tearDown(void) {
  for (int i = 0; i < TEST_TOUCH_CHANNEL; i++) {
          test_release_fake(touch_list[i]);
  }
  delay(100);
}
  
/*
 * Test Touch read on all available channels - compare values if reading is right
 */
void test_touch_read(void) {

  //TEST RELEASE STATE
  for (int i = 0; i < sizeof(TOUCH_GPIOS); i++) {
        #ifdef CONFIG_IDF_TARGET_ESP32
          TEST_ASSERT_GREATER_THAN(RELEASED_VALUE, touchRead(TOUCH_GPIOS[i]));
        #else
          TEST_ASSERT_LESS_THAN(RELEASED_VALUE, touchRead(TOUCH_GPIOS[i]));
        #endif
  }

  // TEST PRESS STATE
  for (int j = 0; j < TEST_TOUCH_CHANNEL; j++) {
          test_press_fake(touch_list[j]);
  }
  delay(100);
  
  for (int k = 0; k < sizeof(TOUCH_GPIOS); k++) {
        #ifdef CONFIG_IDF_TARGET_ESP32
          TEST_ASSERT_LESS_THAN(PRESSED_VALUE,touchRead(TOUCH_GPIOS[k]));
        #else
          TEST_ASSERT_GREATER_THAN(PRESSED_VALUE, touchRead(TOUCH_GPIOS[k]));
        #endif
  }
}

void test_touch_interrtupt(void) {
 
  touchAttachInterrupt(TOUCH_GPIOS[0], gotTouch1, INTERRUPT_THRESHOLD);
  touchAttachInterrupt(TOUCH_GPIOS[1], gotTouch2, INTERRUPT_THRESHOLD);

  test_press_fake(touch_list[0]);
  test_press_fake(touch_list[1]);

  delay(300);
  
  touchDetachInterrupt(TOUCH_GPIOS[0]);
  touchDetachInterrupt(TOUCH_GPIOS[1]);
  
  TEST_ASSERT_TRUE(touch1detected);
  TEST_ASSERT_TRUE(touch2detected);
}

void test_touch_errors(void) {
  
  TEST_ASSERT_FALSE(touchRead(NO_TOUCH_GPIO));
}

void setup() {
  Serial.begin(115200);
  while (!Serial) {
    ;
  }
  
  UNITY_BEGIN();
  RUN_TEST(test_touch_read);
  RUN_TEST(test_touch_interrtupt);
  RUN_TEST(test_touch_errors);
  UNITY_END();
}

void loop() {

}

#else
//PASS TEST for UNSUPPORTED CHIPS

void test_pass(void){
  TEST_ASSERT_EQUAL(1, 1);
}

void setup() {
  Serial.begin(115200);
  while (!Serial) {
    ;
  }
  
  UNITY_BEGIN();
  RUN_TEST(test_pass);
  UNITY_END();
}

void loop() {

}

#endif