feat(i2s): Add I2S examples

- ES8388 loopback example using the LyraT board
- ESP32-S3-EYE record WAV to SD card example
- Simple tone example

Author: lucasssvaz

libraries/ESP_I2S/examples/ES8388_loopback/ES8388.cpp

@@ -0,0 +1,86 @@
+/*
+  ESP32-LyraT I2S ES8388 loopback example
+  This simple example demonstrates using the I2S library in combination
+  with the ES8388 codec on the ESP32-LyraT board to record and play back
+  audio data.
+
+  Don't forget to enable the PSRAM in the Tools menu!
+
+  Created for arduino-esp32 on 20 Dec, 2023
+  by Lucas Saavedra Vaz (lucasssvaz)
+*/
+
+#include "ESP_I2S.h"
+#include "Wire.h"
+
+#include "ES8388.h"
+
+/* Pin definitions */
+
+/* I2C */
+const uint8_t I2C_SCL = 23;
+const uint8_t I2C_SDA = 18;
+const uint32_t I2C_FREQ = 400000;
+
+/* I2S */
+const uint8_t I2S_MCLK = 0;      /* Master clock */
+const uint8_t I2S_SCK = 5;       /* Audio data bit clock */
+const uint8_t I2S_WS = 25;       /* Audio data left and right clock */
+const uint8_t I2S_SDOUT = 26;    /* ESP32 audio data output (to speakers) */
+const uint8_t I2S_SDIN = 35;     /* ESP32 audio data input (from microphone) */
+
+/* PA */
+const uint8_t PA_ENABLE = 21;    /* Power amplifier enable */
+
+void setup() {
+  I2SClass i2s;
+  ES8388 codec;
+  uint8_t *wav_buffer;
+  size_t wav_size;
+
+  // Initialize the serial port
+  Serial.begin(115200);
+  while (!Serial) { delay(10); }
+
+  pinMode(PA_ENABLE, OUTPUT);
+  digitalWrite(PA_ENABLE, HIGH);
+
+  Serial.println("Initializing I2C bus...");
+
+  // Initialize the I2C bus
+  Wire.begin(I2C_SDA, I2C_SCL, I2C_FREQ);
+
+  Serial.println("Initializing I2S bus...");
+
+  // Set up the pins used for audio input
+  i2s.setPins(I2S_SCK, I2S_WS, I2S_SDOUT, I2S_SDIN, I2S_MCLK);
+
+  // Initialize the I2S bus in standard mode
+  if (!i2s.begin(I2S_MODE_STD, 44100, I2S_DATA_BIT_WIDTH_16BIT, I2S_SLOT_MODE_STEREO, I2S_STD_SLOT_BOTH)) {
+    Serial.println("Failed to initialize I2S bus!");
+    return;
+  }
+
+  Serial.println("Initializing ES8388...");
+
+  if (!codec.begin(i2s)) {
+    Serial.println("Failed to initialize ES8388!");
+    return;
+  }
+
+  Serial.println("Recording 10 seconds of audio data...");
+
+  // Record 10 seconds of audio data
+  wav_buffer = codec.recordWAV(10, &wav_size);
+
+  Serial.println("Recording complete. Playing audio data in 3 seconds.");
+  delay(3000);
+
+  // Play the audio data
+  Serial.println("Playing audio data...");
+  codec.playWAV(wav_buffer, wav_size);
+
+  Serial.println("Application complete.");
+}
+
+void loop() {}

libraries/ESP_I2S/examples/ES8388_loopback/ES8388.h

@@ -0,0 +1,90 @@
+/*
+  ESP32-S2-EYE I2S record to WAV example
+  This simple example demonstrates using the I2S library to record
+  5 seconds of audio data and write it to a WAV file on the SD card.
+
+  Don't forget to select the OPI PSRAM, 8MB flash size and Enable USB CDC
+  on boot in the Tools menu!
+
+  Created for arduino-esp32 on 18 Dec, 2023
+  by Lucas Saavedra Vaz (lucasssvaz)
+*/
+
+#include "ESP_I2S.h"
+#include "FS.h"
+#include "SD_MMC.h"
+
+const uint8_t I2S_SCK = 41;
+const uint8_t I2S_WS = 42;
+const uint8_t I2S_DIN = 2;
+
+const uint8_t SD_CMD = 38;
+const uint8_t SD_CLK = 39;
+const uint8_t SD_DATA0 = 40;
+
+void setup() {
+  // Create an instance of the I2SClass
+  I2SClass i2s;
+
+  // Create variables to store the audio data
+  uint8_t *wav_buffer;
+  size_t wav_size;
+
+  // Initialize the serial port
+  Serial.begin(115200);
+  while (!Serial) { delay(10); }
+
+  Serial.println("Initializing I2S bus...");
+
+  // Set up the pins used for audio input
+  i2s.setPins(I2S_SCK, I2S_WS, -1, I2S_DIN);
+
+  // Initialize the I2S bus in standard mode
+  if (!i2s.begin(I2S_MODE_STD, 16000, I2S_DATA_BIT_WIDTH_32BIT, I2S_SLOT_MODE_MONO, I2S_STD_SLOT_LEFT)) {
+    Serial.println("Failed to initialize I2S bus!");
+    return;
+  }
+
+  Serial.println("I2S bus initialized.");
+  Serial.println("Initializing SD card...");
+
+  // Set up the pins used for SD card access
+  if (!SD_MMC.setPins(SD_CLK, SD_CMD, SD_DATA0)) {
+    Serial.println("Failed to set SD pins!");
+    return;
+  }
+
+  // Mount the SD card
+  if(!SD_MMC.begin("/sdcard", true)){
+    Serial.println("Failed to initialize SD card!");
+    return;
+  }
+
+  Serial.println("SD card initialized.");
+  Serial.println("Recording 5 seconds of audio data...");
+
+  // Record 5 seconds of audio data
+  wav_buffer = i2s.recordWAV(5, &wav_size);
+
+  // Create a file on the SD card
+  File file = SD_MMC.open("/test.wav", FILE_WRITE);
+  if (!file) {
+    Serial.println("Failed to open file for writing!");
+    return;
+  }
+
+  Serial.println("Writing audio data to file...");
+
+  // Write the audio data to the file
+  if (file.write(wav_buffer, wav_size) != wav_size) {
+    Serial.println("Failed to write audio data to file!");
+    return;
+  }
+
+  // Close the file
+  file.close();
+
+  Serial.println("Application complete.");
+}
+
+void loop() {}

libraries/ESP_I2S/examples/ES8388_loopback/ES8388_loopback.ino

@@ -0,0 +1,68 @@
+/*
+ This example generates a square wave based tone at a specified frequency
+ and sample rate. Then outputs the data using the I2S interface to a
+ MAX08357 I2S Amp Breakout board.
+ I2S Circuit:
+ * Arduino/Genuino Zero, MKR family and Nano 33 IoT
+ * MAX08357:
+   * GND connected GND
+   * VIN connected 5V
+   * LRC connected to pin 0 (Zero) or 3 (MKR), A2 (Nano) or 25 (ESP32)
+   * BCLK connected to pin 1 (Zero) or 2 (MKR), A3 (Nano) or 5 (ESP32)
+   * DIN connected to pin 9 (Zero) or A6 (MKR), 4 (Nano) or 26 (ESP32)
+ DAC Circuit:
+ * ESP32 or ESP32-S2
+ * Audio amplifier
+   - Note:
+     - ESP32 has DAC on GPIO pins 25 and 26.
+     - ESP32-S2 has DAC on GPIO pins 17 and 18.
+  - Connect speaker(s) or headphones.
+ created 17 November 2016
+ by Sandeep Mistry
+ For ESP extended
+ Tomas Pilny
+ 2nd September 2021
+ Lucas Saavedra Vaz (lucasssvaz)
+ 22nd December 2023
+ */
+
+#include <ESP_I2S.h>
+
+const int frequency = 440; // frequency of square wave in Hz
+const int amplitude = 500; // amplitude of square wave
+const int sampleRate = 8000; // sample rate in Hz
+
+i2s_data_bit_width_t bps = I2S_DATA_BIT_WIDTH_16BIT;
+i2s_mode_t mode = I2S_MODE_STD;
+i2s_slot_mode_t slot = I2S_SLOT_MODE_STEREO;
+
+const int halfWavelength = (sampleRate / frequency); // half wavelength of square wave
+
+int32_t sample = amplitude; // current sample value
+int count = 0;
+
+I2SClass i2s;
+
+void setup() {
+  Serial.begin(115200);
+  Serial.println("I2S simple tone");
+
+  // start I2S at the sample rate with 16-bits per sample
+  if (!i2s.begin(mode, sampleRate, bps, slot)) {
+    Serial.println("Failed to initialize I2S!");
+    while (1); // do nothing
+  }
+}
+
+void loop() {
+    if (count % halfWavelength == 0 ) {
+      // invert the sample every half wavelength count multiple to generate square wave
+      sample = -1 * sample;
+    }
+
+	i2s.write(sample); // Right channel
+	i2s.write(sample); // Left channel
+
+    // increment the counter for the next sample
+    count++;
+}