esp32-hal-i2c.c

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#include "esp32-hal-i2c.h"
#include "esp32-hal.h"
#if !CONFIG_DISABLE_HAL_LOCKS
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "freertos/semphr.h"
#endif
#include "esp_attr.h"
#include "esp_system.h"
#include "soc/soc_caps.h"
#include "soc/i2c_periph.h"
#include "hal/i2c_hal.h"
#include "hal/i2c_ll.h"
#include "driver/i2c.h"

typedef volatile struct {
    bool initialized;
    uint32_t frequency;
#if !CONFIG_DISABLE_HAL_LOCKS
    SemaphoreHandle_t lock;
#endif
} i2c_bus_t;

static i2c_bus_t bus[SOC_I2C_NUM];

bool i2cIsInit(uint8_t i2c_num){
    if(i2c_num >= SOC_I2C_NUM){
        return false;
    }
    return bus[i2c_num].initialized;
}

esp_err_t i2cInit(uint8_t i2c_num, int8_t sda, int8_t scl, uint32_t frequency){
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    if(bus[i2c_num].lock == NULL){
        bus[i2c_num].lock = xSemaphoreCreateMutex();
        if(bus[i2c_num].lock == NULL){
            log_e("xSemaphoreCreateMutex failed");
            return ESP_ERR_NO_MEM;
        }
    }
    //acquire lock
    if(xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return ESP_FAIL;
    }
#endif
    if(bus[i2c_num].initialized){
        log_e("bus is already initialized");
        return ESP_FAIL;
    }

    if(!frequency){
        frequency = 100000UL;
    } else if(frequency > 1000000UL){
        frequency = 1000000UL;
    }

    i2c_config_t conf = { };
    conf.mode = I2C_MODE_MASTER;
    conf.scl_io_num = (gpio_num_t)scl;
    conf.sda_io_num = (gpio_num_t)sda;
    conf.scl_pullup_en = GPIO_PULLUP_ENABLE;
    conf.sda_pullup_en = GPIO_PULLUP_ENABLE;
    conf.master.clk_speed = frequency;
    conf.clk_flags = I2C_SCLK_SRC_FLAG_FOR_NOMAL; //Any one clock source that is available for the specified frequency may be choosen

    esp_err_t ret = i2c_param_config((i2c_port_t)i2c_num, &conf);
    if (ret != ESP_OK) {
        log_e("i2c_param_config failed");
    } else {
        ret = i2c_driver_install((i2c_port_t)i2c_num, conf.mode, 0, 0, 0);
        if (ret != ESP_OK) {
            log_e("i2c_driver_install failed");
        } else {
            bus[i2c_num].initialized = true;
            bus[i2c_num].frequency = frequency;
            //Clock Stretching Timeout: 20b:esp32, 5b:esp32-c3, 24b:esp32-s2
            i2c_set_timeout((i2c_port_t)i2c_num, I2C_LL_MAX_TIMEOUT);
        }
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return ret;
}

esp_err_t i2cDeinit(uint8_t i2c_num){
    esp_err_t err = ESP_FAIL;
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //acquire lock
    if(bus[i2c_num].lock == NULL || xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return err;
    }
#endif
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
    } else {
        err = i2c_driver_delete((i2c_port_t)i2c_num);
        if(err == ESP_OK){
            bus[i2c_num].initialized = false;
        }
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return err;
}

esp_err_t i2cWrite(uint8_t i2c_num, uint16_t address, const uint8_t* buff, size_t size, uint32_t timeOutMillis){
    esp_err_t ret = ESP_FAIL;
    i2c_cmd_handle_t cmd = NULL;
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //acquire lock
    if(bus[i2c_num].lock == NULL || xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return ret;
    }
#endif
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
        goto end;
    }
    
    //short implementation does not support zero size writes (example when scanning) PR in IDF?
    //ret =  i2c_master_write_to_device((i2c_port_t)i2c_num, address, buff, size, timeOutMillis / portTICK_RATE_MS);

    ret = ESP_OK;
    uint8_t cmd_buff[I2C_LINK_RECOMMENDED_SIZE(1)] = { 0 };
    cmd = i2c_cmd_link_create_static(cmd_buff, I2C_LINK_RECOMMENDED_SIZE(1));
    ret = i2c_master_start(cmd);
    if (ret != ESP_OK) {
        goto end;
    }
    ret = i2c_master_write_byte(cmd, (address << 1) | I2C_MASTER_WRITE, true);
    if (ret != ESP_OK) {
        goto end;
    }
    if(size){
        ret = i2c_master_write(cmd, buff, size, true);
        if (ret != ESP_OK) {
            goto end;
        }
    }
    ret = i2c_master_stop(cmd);
    if (ret != ESP_OK) {
        goto end;
    }
    ret = i2c_master_cmd_begin((i2c_port_t)i2c_num, cmd, timeOutMillis / portTICK_RATE_MS);

end:
    if(cmd != NULL){
        i2c_cmd_link_delete_static(cmd);
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return ret;
}

esp_err_t i2cRead(uint8_t i2c_num, uint16_t address, uint8_t* buff, size_t size, uint32_t timeOutMillis, size_t *readCount){
    esp_err_t ret = ESP_FAIL;
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //acquire lock
    if(bus[i2c_num].lock == NULL || xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return ret;
    }
#endif
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
    } else {
        ret = i2c_master_read_from_device((i2c_port_t)i2c_num, address, buff, size, timeOutMillis / portTICK_RATE_MS);
        if(ret == ESP_OK){
            *readCount = size;
        } else {
            *readCount = 0;
        }
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return ret;
}

esp_err_t i2cWriteReadNonStop(uint8_t i2c_num, uint16_t address, const uint8_t* wbuff, size_t wsize, uint8_t* rbuff, size_t rsize, uint32_t timeOutMillis, size_t *readCount){
    esp_err_t ret = ESP_FAIL;
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //acquire lock
    if(bus[i2c_num].lock == NULL || xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return ret;
    }
#endif
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
    } else {
        ret = i2c_master_write_read_device((i2c_port_t)i2c_num, address, wbuff, wsize, rbuff, rsize, timeOutMillis / portTICK_RATE_MS);
        if(ret == ESP_OK){
            *readCount = rsize;
        } else {
            *readCount = 0;
        }
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return ret;
}

esp_err_t i2cSetClock(uint8_t i2c_num, uint32_t frequency){
    esp_err_t ret = ESP_FAIL;
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
#if !CONFIG_DISABLE_HAL_LOCKS
    //acquire lock
    if(bus[i2c_num].lock == NULL || xSemaphoreTake(bus[i2c_num].lock, portMAX_DELAY) != pdTRUE){
        log_e("could not acquire lock");
        return ret;
    }
#endif
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
        goto end;
    }
    if(bus[i2c_num].frequency == frequency){
        ret = ESP_OK;
        goto end;
    }
    if(!frequency){
        frequency = 100000UL;
    } else if(frequency > 1000000UL){
        frequency = 1000000UL;
    }
    // Freq limitation when using different clock sources
    #define I2C_CLK_LIMIT_REF_TICK            (1 * 1000 * 1000 / 20)    /*!< Limited by REF_TICK, no more than REF_TICK/20*/
    #define I2C_CLK_LIMIT_APB                 (80 * 1000 * 1000 / 20)   /*!< Limited by APB, no more than APB/20*/
    #define I2C_CLK_LIMIT_RTC                 (20 * 1000 * 1000 / 20)   /*!< Limited by RTC, no more than RTC/20*/
    #define I2C_CLK_LIMIT_XTAL                (40 * 1000 * 1000 / 20)   /*!< Limited by RTC, no more than XTAL/20*/

    typedef struct {
        uint8_t character;          /*!< I2C source clock characteristic */
        uint32_t clk_freq;          /*!< I2C source clock frequency */
    } i2c_clk_alloc_t;

    // i2c clock characteristic, The order is the same as i2c_sclk_t.
    static i2c_clk_alloc_t i2c_clk_alloc[I2C_SCLK_MAX] = {
        {0, 0},
    #if SOC_I2C_SUPPORT_APB
        {0, I2C_CLK_LIMIT_APB},                                                                /*!< I2C APB clock characteristic*/
    #endif
    #if SOC_I2C_SUPPORT_XTAL
        {0, I2C_CLK_LIMIT_XTAL},                                                               /*!< I2C XTAL characteristic*/
    #endif
    #if SOC_I2C_SUPPORT_RTC
        {I2C_SCLK_SRC_FLAG_LIGHT_SLEEP | I2C_SCLK_SRC_FLAG_AWARE_DFS, I2C_CLK_LIMIT_RTC},      /*!< I2C 20M RTC characteristic*/
    #endif
    #if SOC_I2C_SUPPORT_REF_TICK
        {I2C_SCLK_SRC_FLAG_AWARE_DFS, I2C_CLK_LIMIT_REF_TICK},                                 /*!< I2C REF_TICK characteristic*/
    #endif
    };

    i2c_sclk_t src_clk = I2C_SCLK_DEFAULT;
    ret = ESP_OK;
    for (i2c_sclk_t clk = I2C_SCLK_DEFAULT + 1; clk < I2C_SCLK_MAX; clk++) {
#if CONFIG_IDF_TARGET_ESP32S3
        if (clk == I2C_SCLK_RTC) { // RTC clock for s3 is unaccessable now.
            continue;
        }
#endif
        if (frequency <= i2c_clk_alloc[clk].clk_freq) {
            src_clk = clk;
            break;
        }
    }
    if(src_clk == I2C_SCLK_MAX){
        log_e("clock source could not be selected");
        ret = ESP_FAIL;
    } else {
        i2c_hal_context_t hal;
        hal.dev = I2C_LL_GET_HW(i2c_num);
        i2c_hal_set_bus_timing(&(hal), frequency, src_clk);
        bus[i2c_num].frequency = frequency;
        //Clock Stretching Timeout: 20b:esp32, 5b:esp32-c3, 24b:esp32-s2
        i2c_set_timeout((i2c_port_t)i2c_num, I2C_LL_MAX_TIMEOUT);
    }

end:
#if !CONFIG_DISABLE_HAL_LOCKS
    //release lock
    xSemaphoreGive(bus[i2c_num].lock);
#endif
    return ret;
}

esp_err_t i2cGetClock(uint8_t i2c_num, uint32_t * frequency){
    if(i2c_num >= SOC_I2C_NUM){
        return ESP_ERR_INVALID_ARG;
    }
    if(!bus[i2c_num].initialized){
        log_e("bus is not initialized");
        return ESP_FAIL;
    }
    *frequency = bus[i2c_num].frequency;
    return ESP_OK;
}