Add Camera WebServer Example

Author: me-no-dev

Diff for: libraries/ESP32/examples/Camera/CameraWebServer/CameraWebServer.ino

@@ -0,0 +1,148 @@
+#include "esp_camera.h"
+#include <WiFi.h>
+
+//
+// WARNING!!! Make sure that you have either selected ESP32 Wrover Module,
+//            or another board which has PSRAM enabled
+//
+
+// Select camera model
+#define CAMERA_MODEL_WROVER_KIT
+//#define CAMERA_MODEL_M5STACK_PSRAM
+//#define CAMERA_MODEL_AI_THINKER
+
+const char* ssid = "*********";
+const char* password = "*********";
+
+
+#if defined(CAMERA_MODEL_WROVER_KIT)
+#define PWDN_GPIO_NUM    -1
+#define RESET_GPIO_NUM   -1
+#define XCLK_GPIO_NUM    21
+#define SIOD_GPIO_NUM    26
+#define SIOC_GPIO_NUM    27
+
+#define Y9_GPIO_NUM      35
+#define Y8_GPIO_NUM      34
+#define Y7_GPIO_NUM      39
+#define Y6_GPIO_NUM      36
+#define Y5_GPIO_NUM      19
+#define Y4_GPIO_NUM      18
+#define Y3_GPIO_NUM       5
+#define Y2_GPIO_NUM       4
+#define VSYNC_GPIO_NUM   25
+#define HREF_GPIO_NUM    23
+#define PCLK_GPIO_NUM    22
+
+#elif defined(CAMERA_MODEL_M5STACK_PSRAM)
+#define PWDN_GPIO_NUM     -1
+#define RESET_GPIO_NUM    15
+#define XCLK_GPIO_NUM     27
+#define SIOD_GPIO_NUM     25
+#define SIOC_GPIO_NUM     23
+
+#define Y9_GPIO_NUM       19
+#define Y8_GPIO_NUM       36
+#define Y7_GPIO_NUM       18
+#define Y6_GPIO_NUM       39
+#define Y5_GPIO_NUM        5
+#define Y4_GPIO_NUM       34
+#define Y3_GPIO_NUM       35
+#define Y2_GPIO_NUM       32
+#define VSYNC_GPIO_NUM    22
+#define HREF_GPIO_NUM     26
+#define PCLK_GPIO_NUM     21
+
+#elif defined(CAMERA_MODEL_AI_THINKER)
+#define PWDN_GPIO_NUM     32
+#define RESET_GPIO_NUM    -1
+#define XCLK_GPIO_NUM      0
+#define SIOD_GPIO_NUM     26
+#define SIOC_GPIO_NUM     27
+
+#define Y9_GPIO_NUM       35
+#define Y8_GPIO_NUM       34
+#define Y7_GPIO_NUM       39
+#define Y6_GPIO_NUM       36
+#define Y5_GPIO_NUM       21
+#define Y4_GPIO_NUM       19
+#define Y3_GPIO_NUM       18
+#define Y2_GPIO_NUM        5
+#define VSYNC_GPIO_NUM    25
+#define HREF_GPIO_NUM     23
+#define PCLK_GPIO_NUM     22
+
+#else
+#error "Camera model not selected"
+#endif
+
+void startCameraServer();
+
+void setup() {
+  Serial.begin(115200);
+  Serial.setDebugOutput(true);
+  Serial.println();
+
+  camera_config_t config;
+  config.ledc_channel = LEDC_CHANNEL_0;
+  config.ledc_timer = LEDC_TIMER_0;
+  config.pin_d0 = Y2_GPIO_NUM;
+  config.pin_d1 = Y3_GPIO_NUM;
+  config.pin_d2 = Y4_GPIO_NUM;
+  config.pin_d3 = Y5_GPIO_NUM;
+  config.pin_d4 = Y6_GPIO_NUM;
+  config.pin_d5 = Y7_GPIO_NUM;
+  config.pin_d6 = Y8_GPIO_NUM;
+  config.pin_d7 = Y9_GPIO_NUM;
+  config.pin_xclk = XCLK_GPIO_NUM;
+  config.pin_pclk = PCLK_GPIO_NUM;
+  config.pin_vsync = VSYNC_GPIO_NUM;
+  config.pin_href = HREF_GPIO_NUM;
+  config.pin_sscb_sda = SIOD_GPIO_NUM;
+  config.pin_sscb_scl = SIOC_GPIO_NUM;
+  config.pin_pwdn = PWDN_GPIO_NUM;
+  config.pin_reset = RESET_GPIO_NUM;
+  config.xclk_freq_hz = 20000000;
+  config.pixel_format = PIXFORMAT_JPEG;
+  //init with high specs to pre-allocate larger buffers
+  if(psramFound()){
+    config.frame_size = FRAMESIZE_UXGA;
+    config.jpeg_quality = 10;
+    config.fb_count = 2;
+  } else {
+    config.frame_size = FRAMESIZE_SVGA;
+    config.jpeg_quality = 12;
+    config.fb_count = 1;
+  }
+
+  // camera init
+  esp_err_t err = esp_camera_init(&config);
+  if (err != ESP_OK) {
+    Serial.printf("Camera init failed with error 0x%x", err);
+    return;
+  }
+
+  //drop down frame size for higher initial frame rate
+  sensor_t * s = esp_camera_sensor_get();
+  s->set_framesize(s, FRAMESIZE_CIF);
+
+  WiFi.begin(ssid, password);
+
+  while (WiFi.status() != WL_CONNECTED) {
+    delay(500);
+    Serial.print(".");
+  }
+  Serial.println("");
+  Serial.println("WiFi connected");
+
+  startCameraServer();
+
+  Serial.print("Camera Ready! Use 'http://");
+  Serial.print(WiFi.localIP());
+  Serial.println("' to connect");
+}
+
+void loop() {
+  // put your main code here, to run repeatedly:
+
+}