esp32-hal-i2c.c

// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#include "esp32-hal-i2c.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "rom/ets_sys.h"
#include "soc/i2c_reg.h"
#include "soc/dport_reg.h"

#define I2C_DEV(i)   (volatile i2c_dev_t *)((i)?DR_REG_I2C1_EXT_BASE:DR_REG_I2C_EXT_BASE)
//#define I2C_DEV(i)   ((i2c_dev_t *)(REG_I2C_BASE(i)))
#define I2C_SCL_IDX(p)  ((p==0)?I2CEXT0_SCL_OUT_IDX:((p==1)?I2CEXT1_SCL_OUT_IDX:0))
#define I2C_SDA_IDX(p) ((p==0)?I2CEXT0_SDA_OUT_IDX:((p==1)?I2CEXT1_SDA_OUT_IDX:0))

void i2cAttachSCL(i2c_t * i2c, int8_t scl)
{
    pinMode(scl, OUTPUT);
    pinMatrixOutAttach(scl, I2C_SCL_IDX(i2c->num), false, false);
    pinMatrixInAttach(scl, I2C_SCL_IDX(i2c->num), false);
}

void i2cDetachSCL(i2c_t * i2c, int8_t scl)
{
    pinMatrixOutDetach(scl, false, false);
    pinMatrixInDetach(I2C_SCL_IDX(i2c->num), false, false);
    pinMode(scl, INPUT);
}

void i2cAttachSDA(i2c_t * i2c, int8_t sda)
{
    pinMode(sda, OUTPUT_OPEN_DRAIN);
    pinMatrixOutAttach(sda, I2C_SDA_IDX(i2c->num), false, false);
    pinMatrixInAttach(sda, I2C_SDA_IDX(i2c->num), false);
}

void i2cDetachSDA(i2c_t * i2c, int8_t sda)
{
    pinMatrixOutDetach(sda, false, false);
    pinMatrixInDetach(I2C_SDA_IDX(i2c->num), false, false);
    pinMode(sda, INPUT);
}

enum {
    I2C_CMD_RSTART,
    I2C_CMD_WRITE,
    I2C_CMD_READ,
    I2C_CMD_STOP,
    I2C_CMD_END
};

/*
 * index     - command index (0 to 15)
 * op_code   - is the command
 * byte_num  - This register is to store the amounts of data that is read and written. byte_num in RSTART, STOP, END is null.
 * ack_val   - Each data byte is terminated by an ACK bit used to set the bit level.
 * ack_exp   - This bit is to set an expected ACK value for the transmitter.
 * ack_check - This bit is to decide whether the transmitter checks ACK bit. 1 means yes and 0 means no.
 * */
void i2cSetCmd(i2c_t * i2c, uint8_t index, uint8_t op_code, uint8_t byte_num, bool ack_val, bool ack_exp, bool ack_check)
{
    i2c->dev->command[index].val = 0;
    i2c->dev->command[index].ack_en = ack_check;
    i2c->dev->command[index].ack_exp = ack_exp;
    i2c->dev->command[index].ack_val = ack_val;
    i2c->dev->command[index].byte_num = byte_num;
    i2c->dev->command[index].op_code = op_code;
}

int i2cWrite(i2c_t * i2c, uint16_t address, bool addr_10bit, uint8_t * data, uint8_t len, bool sendStop)
{
    int i;
    uint8_t index = 0;
    uint8_t dataLen = len + (addr_10bit?2:1);
    address = (address << 1);

    while(dataLen) {
        uint8_t willSend = (dataLen > 32)?32:dataLen;
        uint8_t dataSend = willSend;

        //CMD START
        i2cSetCmd(i2c, 0, I2C_CMD_RSTART, 0, false, false, false);

        //CMD WRITE(ADDRESS + DATA)
        if(!index) {
            i2c->dev->fifo_data.data = address & 0xFF;
            dataSend--;
            if(addr_10bit) {
                i2c->dev->fifo_data.data = (address >> 8) & 0xFF;
                dataSend--;
            }
        }
        i = 0;
        while(i<dataSend) {
            i++;
            i2c->dev->fifo_data.data = data[index++];
        }
        i2cSetCmd(i2c, 1, I2C_CMD_WRITE, willSend, false, false, true);
        dataLen -= willSend;

        //CMD STOP or CMD END if there is more data
        if(dataLen) {
            i2cSetCmd(i2c, 2, I2C_CMD_END, 0, false, false, false);
        } else if(sendStop) {
            i2cSetCmd(i2c, 2, I2C_CMD_STOP, 0, false, false, false);
        }

        //Clear Interrupts
        i2c->dev->int_clr.val = 0xFFFFFFFF;

        //START Transmission
        i2c->dev->ctr.trans_start = 1;

        //WAIT Transmission
        while(1) {
            if(i2c->dev->ctr.trans_start || i2c->dev->status_reg.bus_busy || !(i2c->dev->int_raw.trans_complete) || !(i2c->dev->command[2].done)) {
                continue;
            } else if(i2c->dev->int_raw.ack_err || i2c->dev->int_raw.time_out || i2c->dev->int_raw.arbitration_lost) {
                break;
            } else if(i2c->dev->command[2].done) {
                break;
            }
        }

        //Bus failed (maybe check for this while waiting?
        if(i2c->dev->int_raw.arbitration_lost) {
            //log_e("Bus Fail! Addr: %x", address >> 1);
            return 4;
        }

        //Bus timeout
        if(i2c->dev->int_raw.time_out) {
            //log_e("Bus Timeout! Addr: %x", address >> 1);
            return 3;
        }

        //Transmission did not finish and ACK_ERR is set
        if(i2c->dev->int_raw.ack_err) {
            //log_e("Ack Error! Addr: %x", address >> 1);
            return 1;
        }

    }
    return 0;
}

int i2cRead(i2c_t * i2c, uint16_t address, bool addr_10bit, uint8_t * data, uint8_t len, bool sendStop)
{
    address = (address << 1) | 1;
    uint8_t addrLen = (addr_10bit?2:1);
    uint8_t index = 0;
    uint8_t cmdIdx;
    uint8_t willRead;

    //CMD START
    i2cSetCmd(i2c, 0, I2C_CMD_RSTART, 0, false, false, false);

    //CMD WRITE ADDRESS
    i2c->dev->fifo_data.data = address & 0xFF;
    if(addr_10bit) {
        i2c->dev->fifo_data.data = (address >> 8) & 0xFF;
    }
    i2cSetCmd(i2c, 1, I2C_CMD_WRITE, addrLen, false, false, true);

    while(len) {
        cmdIdx = (index)?0:2;
        willRead = (len > 32)?32:(len-1);
        i2cSetCmd(i2c, cmdIdx++, I2C_CMD_READ, willRead, false, false, false);
        if((len - willRead) > 1) {
            i2cSetCmd(i2c, cmdIdx++, I2C_CMD_END, 0, false, false, false);
        } else {
            willRead++;
            i2cSetCmd(i2c, cmdIdx++, I2C_CMD_READ, 1, true, false, false);
            if(sendStop) {
                i2cSetCmd(i2c, cmdIdx++, I2C_CMD_STOP, 0, false, false, false);
            }
        }

        //Clear Interrupts
        i2c->dev->int_clr.val = 0xFFFFFFFF;

        //START Transmission
        i2c->dev->ctr.trans_start = 1;

        //WAIT Transmission
        while(1) {
            if(i2c->dev->ctr.trans_start || i2c->dev->status_reg.bus_busy || !(i2c->dev->int_raw.trans_complete) || !(i2c->dev->command[cmdIdx-1].done)) {
                continue;
            } else if(i2c->dev->int_raw.ack_err || i2c->dev->int_raw.time_out || i2c->dev->int_raw.arbitration_lost) {
                break;
            } else if(i2c->dev->command[cmdIdx-1].done) {
                break;
            }
        }

        //Bus failed (maybe check for this while waiting?
        if(i2c->dev->int_raw.arbitration_lost) {
            //log_e("Bus Fail! Addr: %x", address >> 1);
            return -4;
        }

        //Bus timeout
        if(i2c->dev->int_raw.time_out) {
            //log_e("Bus Timeout! Addr: %x", address >> 1);
            return -3;
        }

        //Transmission did not finish and ACK_ERR is set
        if(i2c->dev->int_raw.ack_err) {
            //log_e("Ack Error! Addr: %x", address >> 1);
            return -1;
        }
        int i = 0;
        while(i<willRead) {
            i++;
            data[index++] = i2c->dev->fifo_data.data;
        }
        len -= willRead;
    }
    return 0;
}

void i2cResetFiFo(i2c_t * i2c)
{
    //TX FIFO
    i2c->dev->fifo_conf.tx_fifo_rst = 1;
    i2c->dev->fifo_conf.tx_fifo_rst = 0;
    //RX FIFO
    i2c->dev->fifo_conf.rx_fifo_rst = 1;
    i2c->dev->fifo_conf.rx_fifo_rst = 0;
}

void i2cSetFrequency(i2c_t * i2c, uint32_t clk_speed)
{
    uint32_t period = (APB_CLK_FREQ/clk_speed) / 2;
    i2c->dev->scl_low_period.scl_low_period = period;
    i2c->dev->scl_high_period.period = period;

    i2c->dev->scl_start_hold.time = 50;
    i2c->dev->scl_rstart_setup.time = 50;

    i2c->dev->scl_stop_hold.time   = 50;
    i2c->dev->scl_stop_setup.time = 50;

    i2c->dev->sda_hold.time     = 25;
    i2c->dev->sda_sample.time = 25;
}

uint32_t i2cGetFrequency(i2c_t * i2c)
{
    return APB_CLK_FREQ/(i2c->dev->scl_low_period.scl_low_period+i2c->dev->scl_high_period.period);
}

/*
 * mode          - 0 = Slave, 1 = Master
 * slave_addr    - I2C Address
 * addr_10bit_en - enable slave 10bit address mode.
 * */

i2c_t * i2cInit(uint8_t i2c_num, uint16_t slave_addr, bool addr_10bit_en)
{
    i2c_t* i2c = (i2c_t*) malloc(sizeof(i2c_t));
    if(i2c == 0) {
        return NULL;
    }

    i2c->num = i2c_num;
    i2c->dev = I2C_DEV(i2c_num);

    if(i2c->num == 0) {
        SET_PERI_REG_MASK(DPORT_PERIP_CLK_EN_REG,DPORT_I2C_EXT0_CLK_EN);
        CLEAR_PERI_REG_MASK(DPORT_PERIP_RST_EN_REG,DPORT_I2C_EXT0_RST);
    } else if(i2c->num == 1) {
        SET_PERI_REG_MASK(DPORT_PERIP_CLK_EN_REG,DPORT_I2C_EXT1_CLK_EN);
        CLEAR_PERI_REG_MASK(DPORT_PERIP_RST_EN_REG,DPORT_I2C_EXT1_RST);
    }

    i2c->dev->ctr.val = 0;
    i2c->dev->ctr.ms_mode = (slave_addr == 0);
    i2c->dev->ctr.sda_force_out = 1 ;
    i2c->dev->ctr.scl_force_out = 1 ;
    i2c->dev->ctr.clk_en = 1;

    i2c->dev->timeout.tout = 2000;
    i2c->dev->fifo_conf.nonfifo_en = 0;

    i2c->dev->slave_addr.val = 0;
    if (slave_addr) {
        i2c->dev->slave_addr.addr = slave_addr;
        i2c->dev->slave_addr.en_10bit = addr_10bit_en;
    }

    return i2c;
}